Getting garden tools ready for winter: cleaning, sharpening, oiling and storing

When the vegetable garden goes quiet in November, it is time to give your tools a thorough service. A clean, sharp spade goes into the soil more easily, and a well-sharpened pair of secateurs makes clean cuts that heal faster. What's more, well-maintained tools last for years. With a brush, a file, some oil and an hour of your time you can get a long way.

Why maintenance is worth it

Tools have three enemies: moisture, plant sap and sand. Moisture makes steel rust, plant sap can harbour pathogens, and sand wears cutting edges blunt. Blunt secateurs crush the twig instead of cutting through it. Such a ragged wound heals less well and gives diseases more of a chance. Good secateurs will last many years with maintenance; without it they are worn out after a few seasons.

A handy rhythm: a thorough service in November before everything goes into the shed, and a quick check in early spring.

Step 1: cleaning

  • Remove the soil: knock off caked-on soil and brush the blade clean with a stiff brush or wire brush. Rinse and dry immediately with a cloth.
  • Resin and plant sap: remove these from secateurs and saws with warm water and a scouring pad. Stubborn resin can be loosened with a penetrating oil or methylated spirits.
  • Rust: rub rust spots off with a scouring pad, fine steel wool or sandpaper until you see bare steel again. A paste of baking soda and water can help loosen rust.
  • Disinfecting: if you have pruned diseased plants, wipe the blades of your secateurs with a cloth soaked in alcohol. That way you don't carry diseases into the next season.

An old trick for spades and hoes: push the blade a few times into a bucket of coarse sand mixed with a splash of oil. It scours and protects in one go.

Step 2: repairing

Check everything for loose parts. Tighten nuts and screws, replace missing bolts and secure a wobbly handle. A wooden handle with deep cracks or soft, rotten patches is better replaced, because sooner or later it will break while you are working.

Step 3: sharpening

Shovel, spade and hoe

Clamp the tool in a vice and use a flat file of medium coarseness. Follow the existing angle of the cutting edge; for a spade or hoe this is roughly 30 to 45 degrees. File away from your body and lift the file on the return stroke. Ten strokes per session is usually enough. A spade doesn't need to be razor-sharp, but a sharp edge cuts much more easily through roots and turf.

Secateurs

Secateurs with two blades that slide past each other (so-called bypass secateurs) should only be sharpened on the bevelled upper blade, and only on the bevelled side. Leave the flat lower blade alone; if you sharpen that too, the blades will no longer close properly. Use a small diamond file or sharpening stone and hold it at the same angle as the existing cutting edge. Then remove the burr with a few light strokes along the flat side. If you can take the secateurs apart, sharpening is easier. If you don't dare, take your secateurs and mower blades to a professional sharpener.

Step 4: oiling

  • Steel: rub blades and teeth with a thin layer of oil, such as machine oil or a light vegetable oil. Wipe off the excess.
  • Pivots and springs: a few drops of oil, then open and close the secateurs a number of times.
  • Wooden handles: sand rough spots smooth with fine sandpaper (120 grit) and rub the wood with boiled linseed oil. Let the oil soak in for half an hour and wipe off the rest. Raw linseed oil dries poorly. If the handle is varnished, sand the varnish off first.

A practical point: a penetrating spray such as WD-40 is useful for removing dirt, resin and moisture, but it doesn't leave a lasting protective layer. So apply proper oil afterwards.

Step 5: storing

  • Store tools in a dry, ventilated space, such as a shed or garage. A damp corner against a cold wall is bad for steel.
  • Hang up large tools rather than leaving them on the floor. That way they stay drier and blunt less quickly. Make sure they don't touch each other.
  • Keep small tools together in a bucket or tool bag, so that in spring you can take everything out in one go.

Don't forget the rest

  • Drain hoses and coil them up, and store spray nozzles dry.
  • Turn watering cans and buckets upside down so that no water freezes in them.
  • Petrol machines such as a brushcutter: empty the tank or add a stabiliser so that they start properly in spring.
  • Clean seed trays and pots and stack them, ready for the new sowing season.

Frequently asked questions

Question Answer
How do you get garden tools ready for winter? Give them a thorough going-over in November: clean off soil, sap and rust, mend loose parts, sharpen the cutting edges and rub steel and wooden handles with oil. Then store everything dry in a ventilated shed or garage.
How do you sharpen secateurs? Sharpen bypass secateurs only on the bevelled upper blade, and only on the bevelled side. Leave the flat lower blade alone; if you sharpen that too, the blades will no longer close properly.
Which oil do you use on garden tools? Rub blades, heads and tines with a thin film of machine oil or a light vegetable oil. A penetrating oil such as WD-40 is handy for removing dirt and moisture, but leaves no lasting protective film; so follow it with proper oil. Rub wooden handles with boiled linseed oil.
Why do secateurs need to be sharp? Blunt secateurs crush the twig instead of cutting through it. Such a ragged wound heals less well and gives diseases more chance.
How do you store hoses and watering cans for winter? Drain garden hoses and coil them, and store sprinklers dry. Stand watering cans and buckets upside down so no water freezes in them.

Sources